Saturday 21st April 2007 - 21:27:15

The Rack

I have assembled my rack and fitted all my gear into it. There was some trouble locating the screws to hold on the rack-ears for the Cisco 2924-XL-M switch though. There was some initial trouble with the orientation of the horizontals on the 19" wide side because they did't mesh with the verticals. So I had to pull it all apart (pain in the butt - friction fit joins) and then re-assemble it.

From The Top:
* Cisco 2924-XL-M with 2 x C2922-XL-V Dual 100 Base FX Fiber Modules.
* 3 Empty RU for Potential Cisco Routers Later.
* 56K Dialup Modem, Billion ADSL Router and Netgear Wireless Router.
* IBM 8045-012 Hub - Used for watching the LAN.
* D-Link 14 Port 10 Base T Switch + 2 x 100M uplinks.
* Cable Organiser
* Cisco 4000M with 2 x NP-1E (Ethernet) and 1 x NP-1RV2 (Token Ring) Interfaces.
* Dell Poweredge 2400 Server.

Tomorrow I am going to go through the bits of RC Car that I picked up from Mum and Dad's today. I had the wrong idea about the bits being together, as in something that resembled a car. It will be interesting to see what I can cobble together with these bits. I have a Tamiya Super Hornet with a smashed front, and cracked gearbox, broken wing. I have a Tamiya HotShot which is pretty slawed too. It's actually not in one piece, got cracked suspension mounts (tricky single-shock suspension) and probably gearbox troubles. I also need to fix the front gearbox and re-install the center shaft so that it does 4WD again... I have two body halves, the gear train, shocks and running gear are all in bits in my container (I'm not usually one to misplace bits - although I can forget where I "organised" them to...). I have an Attack II Control in unknown condidtion with - of all things - a 9v battery snap on it that I have obviously modded in there at some time. Ah the modding started early. I have crystals which is an excellent start and two radio recievers. Now one RX is in the parts box and the other is in the car. I'd say one is dead. Guess which =)

Unfortunately I couldn't find my l33t 13T (that's 13 turns), pretty labelled bright looking, fins at the back and replaceable brushes racing motor. It's gotta be somewhere at Mum and Dad's still. That was good I got it for like $5 years and years ago, we are talking pre-highschool. So, I dunno, maybe 8+ years ago. Bougth brushes and stuck them in and cleaned it all up - but never used it.

I have a lot of small nuts, bolts and washers available from my electronics collection that I am pretty sure I will need! I also need to track down some resistors for the speed controllers - or get an ESC. Probably resistors for now 'cus they're going to be free =) In my wisdom I had removed the resistors and jumpered them, so, it's either full-throttle or nothing on the speed control at the moment. Now that I actually know why they are there and what they do - I think I will put them back, they chew power though. I have a backup remote control that I bought for $8.50 from eBay and also a set of ball-bearings for $9 including the teeny tiny ball bearing in the middle of the diff!!! This will help with run-time. Some of the cheaper upgrades until I get a car working ! If I get ambitious I will make my own ESC, I can probably look at that now pretty easilly. There is a DC Motor Controller Kit from *shudder* Dick Smith that would be easy to modify as an ESC. It's a little bigger than a bought one but will pack lots more punch and would have a better current-handling capacity. If not, there's always eBay Cool

Next entry

Previous entry

Similar entries